Aruba AP-584 Outdoor Access Point

Specifications

Models

AP-584

Four dual-band Nf connectors for external antenna operation

One 2.4Ghz IoT Nf connector for the Bluetooth/Zigbee radio

5dBi omni-directional antenna included

WI-FI RADIO SPECIFICATIONS

AP type: Outdoor Hardened, Wi-Fi 6 dual radio, 5GHz and 2.4GHz 802.11ax 4×4 MIMO

Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)

5GHz radio

Four spatial stream Single User (SU) MIMO for up to 2.4Gbps wireless data rate with individual 4SS HE80 (or 2SS HE160) 802.11ax client devices, or with four 1SS or two 2SS HE80 802.11ax MU-MIMO capable client devices simultaneously

2.4GHz radio:

 Four spatial stream Single User (SU) MIMO for up to 1,150Mbps wireless data rate with individual 4SS HE40 802.11ax client devices or with two 2SS HE40 802.11ax MU-MIMO capable client devices simultaneously.

Support for up to 1,024 associated client devices per radio (typical recommended limit for active outdoor clients is 100-200 depending on distance), and up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

2.400 to 2.4835GHz

5.150 to 5.250GHz

5.250 to 5.350GHz

5.470 to 5.725GHz

5.725 to 5.850GHz

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

802.11b: Direct-sequence spread-spectrum (DSSS)

802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 37 resource units (for an 80MHz channel)

Supported modulation types:

802.11b: BPSK, QPSK, CCK

802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension)

802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension)

802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM

802.11n high-throughput (HT) support: HT20/40

802.11ac very high throughput (VHT) support: VHT20/40/80/160

802.11ax high efficiency (HE) support: HE20/40/80/160

Supported data rates (Mbps) :

802.11b: 1, 2, 5.5, 11

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM

802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160), 2,166 with 1024-QAM

802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)

802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160)

802.11n/ac packet aggregation: A-MPDU, A-MSDU

Transmit power: Configurable in increments of 0.5 dBm

Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):

2.4 GHz band: +29 dBm (23dBm per chain)

5 GHz band: +28 dBm (22 dBm per chain)

Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

Transmit beam-forming (TxBF) for increased signal reliability and range

802.11ax Target Wait Time (TWT) to support low-power client devices

Advanced IoT Existence (AIC) allows for concurrent operation of the IoT and 2.4Ghz radios without issue

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks

WI-FI Antennas

AP-584

Four Nf connectors for external dual band antennas (WIFI0 through WIFI3, corresponding with radio chains 0 through 3), and one Nf connector for BT (includes 5dBi 2.4Ghz omni-directional antenna). Worst-case internal loss between radio interface and external antenna connectors: 0.8dB in 2.4GHz(WiFi), 0.8dB in 2.4GHz(BT) and 1.0dB in 5GHz.

OTHER INTERFACES

Wired network interface (E0)

100/1000/2500/5000Base-T Ethernet

5Gbps Smart Rate: NBase-T, 802.3bz

PoE PD support on E0

IEEE/802.3az support

Support for jumbo frames (MTU up to 9,216 bytes)

 Wired network interface (E1)

10GBASE-R SFP+ port

IEEE/802.3az support (as applicable)

Support for jumbo frames (up to 9,216 bytes)

1 x SFP+ cage

When used in operation it is expected that this is the primary uplink port

Only recommended industrial temperature SFP/SFP+ modules should be used for optimal performance

Wired network interface (E2)

10/100/1000BaseT Ethernet

IEEE/802.3az support (as applicable)

Support for jumbo frames (up to 9,216 bytes)

Support for PoE PSE of 802.3af (may be able to reach 802.3at PSE with IPM policy if needed depending on temperature and load)

AC power interface: 110-240V (requires AP-AC-MLX power connector kit)

Bluetooth (BT5.0) and Zigbee (802.15.4) radio

BT: up to 8dBm transmit power (class 2) and -98dBm receive sensitivity (125kbps)

Zigbee: up to 8dBm transmit power and -96dBm receive sensitivity

Visual indictors (multi-color LED): for System and Radio status

Reset button: factory reset, LED mode control (normal/off)

USB-C console interface

Shielded Twisted Pair (STP) Ethernet cable should be used on all Ethernet interfaces for proper surge protection

POWER SOURCES AND POWER CONSUMPTION

The AP supports direct AC power and Power over Ethernet (POE; on port E0 only)

When both AC and POE power sources are available, AC power takes priority over POE

Power sources are sold separately; see the ordering Information section below for details

See below conditions for each power configuration:

When powered by AC, the AP will operate without restrictions, including 802.3af/at support (with upper thermal limitations).* With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce according to established IPM policy

When powered by 802.3bt Class 6, the AP will operate without restriction, limited to 802.3af PSE support.* With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce according to established IPM policy

When powered by 802.3bt Class 5 with LLDP, full function but no PSE support*

When powered by 802.3at, AP will reduce 2.4Ghz to 1 chain, and will reduce the 5Ghz to 3 chains, no PsE out*

When powered by 802.3af, the AP will boot up, but not enable any radios, regardless of IPM settings.

 With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce power as necessary according to the established IPM policy

Maximum (worst-case) power consumption:

AC powered: 71W (802.3af/at*)

POE powered (802.3bt Class 6): 49.5W (802.3af PSE only)

POE powered (802.3bt Class 5 with LLDP): 35.5W (no PSE)

POE powered (802.3at, IPM disabled): 25.5W (1 chain @ 2.4Ghz, 3 chains @ 5Ghz, no PSE)

Maximum (worst-case) power consumption in idle mode: 9.2W (POE) or 10.8W (AC)

Maximum (worst-case) power consumption in deep-sleep mode: 3.0W (POE) or 4.4W (AC)

MOUNTING

AP-OUT-MNT-V1A – Long arm wall or pole mounting bracket

AP-270-MNT-H1 – Single-tilt mounting bracket for wall or ceiling

AP-270-MNT-H2 – Flush ceiling or wall mounting bracket

AP-270-MNT-H3 – Dual-tilt mounting bracket for wall or ceiling

MECHANICAL SPECIFICATIONS

Dimensions/weight (AP-584 unit only):

324mm (W) x 312mm (D) x 244mm (H) / 12.6” (W) x 12.3” (D) x 9.6” (H)

5.52kg / 11.5lbs

Dimensions/weight (AP-584 shipping pkg, no mount):

410mm (W) x 322mm (D) x 433mm (H) / 16.1” (W) x 12.7” (D) x 17” (H)

7.56kg / 16.8lbs

ENVIRONMENTAL

Operating conditions

Temperature: -40°C to +65°C / -40°F to +149°F with full solar loading

Humidity: 5% to 93% non-condensing internal

Rated for operation in all weather conditions

Storage and transportation:

Temperature: -40°C to +70°C / -40°F to +158°F

Water and Dust: IP66/67

Salt Tolerance: Tested to ASTM B117-07A Salt Spray 200hrs

RELIABILITY

Mean Time Between Failure (MTBF): 828,651hrs (~95yrs) at +25°C operating temperature.

REGULATORY

FCC/ISED

CE Marked

RED Directive 2014/53/EU

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

UL/IEC/EN 60950-1

UL/IEC/EN 62368-1

IEC 60950-22

IEC/EN60601-1-2

EN 50155

For more country-specific regulatory information and approvals, please see your Aruba representative.

REGULATORY MODEL NUMBER

AP-584: APEX0584

CERTIFICATIONS

Wi-Fi Alliance:

Bluetooth SIG

Ethernet Alliance (E0, PoE PD device, class 6; E2, PoE PSE device, class 3)

WARRANTY

Aruba’s hardware limited lifetime warranty.

Minimum Software Versions

ArubaOS and Aruba InstantOS 8.10.0.0