Aruba 534 (External Antenna) Access Points

Specifications

AP-534: External antenna models

5GHz: radio

Four spatial stream Single User (SU) MIMO for up to 2.4Gbps wireless data rate with individual 4SS HE80 (or 2SS HE160) 802.11ax client devices, or with four 1SS or two 2SS HE80 802.11ax MU-MIMO capable client devices simultaneously

2.4GHz radio:

Four spatial stream Single User (SU) MIMO for up to 1,150Mbps wireless data rate with individual 4SS HE40 802.11ax client devices or with two 2SS HE40 802.11ax MU-MIMO capable client devices simultaneously

WI-FI RADIO SPECIFICATIONS

AP type: Indoor, dual radio, 5GHz and 2.4GHz 802.11ax 4×4 MIMO

Support for up to 1,024 associated client devices per radio* (typical recommended limit for active clients is 200), and up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

2.400 to 2.4835GHz

5.150 to 5.250GHz

5.250 to 5.350GHz

5.470 to 5.725GHz

5.725 to 5.850GHz

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

802.11b: Direct-sequence spread-spectrum (DSSS)

802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

802.11ax: Orthogonal frequency-division multiple access (OFDMA)* with up to 37 resource units (for an 80MHz channel)

Supported modulation types:

802.11b: BPSK, QPSK, CCK

802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension)

802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM,1024 QAM (proprietary extension)

802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM

802.11n high-throughput (HT) support: HT20/40

802.11ac very high throughput (VHT) support: VHT20/40/80/160

802.11ax high efficiency (HE) support: HE20/40/80/160

Supported data rates (Mbps) :

802.11b: 1, 2, 5.5, 11

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM

802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160), 2,166 with 1024-QAM

802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)

802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160)

802.11n/ac packet aggregation: A-MPDU, A-MSDU

Transmit power: Configurable in increments of 0.5 dBm

Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):

2.4 GHz band: +24 dBm (18dBm per chain)

5 GHz band: +24 dBm (18 dBm per chain)

Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

Transmit beam-forming (TxBF) for increased signal reliability and range

802.11ax Target Wait Time (TWT): To support low-power client devices

*Not initially supported; will be enabled in a future software release

WI-FI ANTENNAS

AP-534

Four (female) RP-SMA connectors for external dual band antennas (A0 through A3, corresponding with radio chains 0 through 3).

Worst-case internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 0.8dB in 2.4GHz and 1.3dB in 5GHz.

OTHER INTERFACES

E0, E1: HPE SmartRate port (RJ-45, maximum negotiated speed 5Gbps)

Auto-sensing link speed (100/1000/2500/5000BASE-T) and MDI/MDX

2.5Gbps and 5Gbps speeds comply with NBase-T and 802.3bz specifications

POE-PD: 48Vdc (nominal) 802.3af/at/bt POE (class 3 or higher)

802.3az Energy Efficient Ethernet (EEE)

Link aggregation (LACP) support between both network ports for redundancy and increased capacity

POE power can be drawn from either port (single source, or set to prioritize) or both ports simultaneously (set to combine) When set to prioritize, the AP draws power from E0 and may failover to E1.

DC power interface

48Vdc (nominal, +/- 5%), accepts 1.35mm/3.5mm center-positive circular plug with 9.5mm length

USB 2.0 host interface (Type A connector)

Capable of sourcing up to 1A / 5W to an attached device

Bluetooth 5.0 Low Energy (BLE5.0) and Zigbee (802.15.4)* radio

BLE: up to 8dBm transmit power (class 1) and -95dBm receive sensitivity

Zigbee: up to 8dBm transmit power and 99dBm receive sensitivity

Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.1dBi (AP-535) or 5.0dBi (AP-534)

Visual indicators (multi-color LEDs):

Power/System status

Radio status

Reset button:

Factory reset, LED mode control (normal/off)

Serial console interface:

Proprietary, micro-B USB physical jack

Kensington security slot

*Not initially supported; will be enabled in a future software release

POWER SOURCES AND POWER CONSUMPTION

Power Sources:

The AP supports direct DC power and Power over Ethernet (POE; on port E0 and/or E1)

When POE power is supplied to both Ethernet ports, the AP can be configured to combine or prioritize power sources

When both DC and POE power sources are available, DC power takes priority over POE

Power sources are sold separately; see the ordering Information section below for details

When powered by DC, 802.3bt (class 5) POE or 2x 802.3at (class 4) POE, the AP will operate without restrictions.

When powered by 1x 802.3at (class 4) POE and with the IPM feature disabled, the AP will disable the USB port and disable the other Ethernet port. In the same configuration but with IPM enabled, the AP will start up in unrestricted mode, but may dynamically apply restrictions depending on the POE budget and actual power. The feature restrictions and order can be programmed.

Operating the AP with an 802.3af (class 3 or lower) POE source is not supported.

Maximum (worst-case) power consumption (without USB or PSE / max):

DC powered: 23.3W

POE powered (802.3bt or dual 802.3at): 26.4W

POE powered (802.3at, IPM disabled): 23.3W

All numbers above are without an external USB device connected. When sourcing the full 5W power budget to such a device, the incremental (worst-case) power consumption for the AP is up to 5.7W ( POE powered) or 5.5W ( DC powered).

Maximum (worst-case) power consumption in idle mode:

13.3W ( POE) or 14.3W (DC)

Maximum (worst-case) power consumption in deep-sleep mode:

3.8W (POE) or 3.6W (DC)

MECHANICAL SPECIFICATIONS

Dimensions/weight

240mm (W) x 240mm (D) x 57mm (H) / 9.4″ (W) x 9.4″ (D) x 2.1″ (H)

1,270g / 44.8oz

Dimensions/weight

285mm (W) x 300mm (D) x 105mm (H) / 11.2″ (W) x 11.9″ (D) x 4.1″ (H)

1,930g / 68.1oz

ENVIRONMENTAL

Operating conditions

Temperature: 0C to +50C / +32F to +122F

Humidity: 5% to 93% non-condensing

AP is plenum rated for use in air-handling spaces

ETS 300 019 class 3.2 environments

Storage and transportation:

Temperature: -40° C to +70° C (-40°F to +158°F)

Humidity: 5% to 93% non-condensing

ETS 300 019 classes 1.2 and 2.3 environments

REGULATORY

FCC/ISED

CE Marked

RED Directive 2014/53/EU

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

UL/IEC/EN 60950

EN 60601-1-1, EN60601-1-2

For more country-specific regulatory information and approvals, please see your Aruba representative.

REGULATORY MODEL NUMBER

AP-534: APIN0534

CERTIFICATIONS

UL2043 plenum rating

Wi-Fi Alliance:

Wi-Fi CERTIFIED a, b, g, n, ac

Wi-Fi CERTIFIED ax1

WPA, WPA2 and WPA3 – Enterprise with CNSA option, Personal (SAE), Enhanced Open (OWE)

WMM, WMM-PS, Wi-Fi Vantage, Wi-Fi Agile Multiband

Wi-Fi Location2

Passpoint (release 2)

Bluetooth SIG

Ethernet Alliance (PoE, PD device, class 6)

RELIABILITY

Mean Time Between Failure (MTBF):

995,000hrs (114yrs) at +25C operating temperature.

Minimum Software Versions

ArubaOS and Aruba InstantOS 8.5.0.0